--- title: "Range error code F1" description: "Frigidaire range error code F1: The control has decided one of its own buttons is being held down." url: "https://frigidairemiami.support/error-codes/range-f1/" date_modified: "2026-09-09" Appliance type: "range" --- # Range error code F1 ### What F1 means on this make The control has decided one of its own buttons is being held down. On this platform the membrane behind the panel is a thin sheet with printed traces, and the two ordinary ways it shorts are heat and moisture — a range that has just finished a self-clean cycle, or a panel that has been cleaned with a wet cloth. Which of the two it was decides whether the code comes back: heat damage is permanent, condensation dries out. This maker publishes the name and a power cycle for it and nothing further, so the reset is worth doing before anything is ordered. ### Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. ### What to do about it - Write the code down exactly as the panel shows it, before you cut power. The display forgets and the condition does not. - Cut power at the breaker for thirty seconds and restore it. This is the maker’s own instruction, and it proves one thing: a code that clears and stays clear was a condition rather than a failure. - Note what the range was doing when it appeared — preheating, mid-bake, self-cleaning, or sitting idle. On a control problem that timing is worth more to a technician than the number. - If it returns, stop resetting it. Three power cycles tell you what one does, and a code that keeps coming back has a part behind it. ### Where this goes next The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. Shorted key pad. Please reset the range by disconnecting the power to the unit for up to 30 seconds. You can disconnect power by either unplugging the unit or flipping the circuit breaker off and back on. What this one means What F1 means on this make The control has decided one of its own buttons is being held down. On this platform the membrane behind the panel is a thin sheet with printed traces, and the two ordinary ways it shorts are heat and moisture — a range that has just finished a self-clean cycle, or a panel that has been cleaned with a wet cloth. Which of the two it was decides whether the code comes back: heat damage is permanent, condensation dries out. This maker publishes the name and a power cycle for it and nothing further, so the reset is worth doing before anything is ordered. Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. What to do about it Write the code down exactly as the panel shows it, before you cut power. The display forgets and the condition does not. Cut power at the breaker for thirty seconds and restore it. This is the maker’s own instruction, and it proves one thing: a code that clears and stays clear was a condition rather than a failure. Note what the range was doing when it appeared — preheating, mid-bake, self-cleaning, or sitting idle. On a control problem that timing is worth more to a technician than the number. If it returns, stop resetting it. Three power cycles tell you what one does, and a code that keeps coming back has a part behind it. Where this goes next The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. --- **[Read full article: Range error code F1](https://frigidairemiami.support/error-codes/range-f1/)**