---
title: "Range error code F10"
description: "Frigidaire range error code F10: The oven is reading a temperature higher than the one it asked for and has stopped itself."
url: "https://frigidairemiami.support/error-codes/range-f10/"
date_modified: "2026-09-09"
Appliance type: "oven, range"
---


# Range error code F10

### What F10 means on this make

The oven is reading a temperature higher than the one it asked for and has stopped itself. That is a protection working rather than a part failing, and the maker says so — its own wording on the ovens guide is that this is a built-in safety alert, and that the range should be turned off and allowed to cool. What sits behind it is usually a relay welded closed or a sensor reading low, so the element stays on past the setpoint. It is the one code on this list we would rather you did not keep resetting past.

### Where this appears, and why not to clear it

On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again.

### What to do about it

- Turn the range off and let it cool completely before using it again — the maker’s own instruction, and the safe one.
- Write the code down and note whether it appeared during baking, during preheat, or during a self-clean cycle. Self-clean is the hardest hour this appliance ever has.
- Cut power at the breaker for thirty seconds and restore it.
- If it comes back, stop using the oven and book the visit. An element that stays energized past the setpoint is not a code to live with.

### Where this goes next

The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything.

Thermal runaway. Please reset the range by disconnecting the power to the unit for up to 30 seconds. You can disconnect power by either unplugging the unit or flipping the circuit breaker off and back on.

What this one means

What F10 means on this make

The oven is reading a temperature higher than the one it asked for and has stopped itself. That is a protection working rather than a part failing, and the maker says so — its own wording on the ovens guide is that this is a built-in safety alert, and that the range should be turned off and allowed to cool. What sits behind it is usually a relay welded closed or a sensor reading low, so the element stays on past the setpoint. It is the one code on this list we would rather you did not keep resetting past.

Where this appears, and why not to clear it

On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again.

What to do about it

Turn the range off and let it cool completely before using it again — the maker’s own instruction, and the safe one.

Write the code down and note whether it appeared during baking, during preheat, or during a self-clean cycle. Self-clean is the hardest hour this appliance ever has.

Cut power at the breaker for thirty seconds and restore it.

If it comes back, stop using the oven and book the visit. An element that stays energized past the setpoint is not a code to live with.

Where this goes next

The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything.

---

**[Read full article: Range error code F10](https://frigidairemiami.support/error-codes/range-f10/)**