--- title: "Washer error code E1" description: "Frigidaire washer error code E1: The machine gave up waiting for a water level it never reached." url: "https://frigidairemiami.support/error-codes/washer-e1/" date_modified: "2026-09-09" Appliance type: "washer" --- # Washer error code E1 ### What E1 means on this make The machine gave up waiting for a water level it never reached. What is useful about this code is how much of it is outside the appliance: two taps, two hoses and two screens, and the screens are where this climate does its work — fine grit and scale collect on the mesh in the inlet valve until the fill slows past the timer. A machine in a condominium laundry closet is also a machine whose taps are behind it and have not been fully opened since the day it was delivered. ### Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. ### Which machines this one applies to Top-load washers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on four kinds of machine — the top-load washer, the dishwasher, the electric range and cooktop, and the refrigerator — and publishes none at all for its dryers, its freezers, its wine cabinets or its ice machines. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door. ### What to do about it - Open both taps fully — not most of the way. A half-open cold tap fills slowly enough to trigger this and fast enough to look normal. - Pull the machine forward and look at the hoses. A hose kinked when the appliance was pushed back is the single most common cause here. - Close the taps, unscrew the hoses at the machine, and clean the screens in the inlet. They are behind the connection and they clog with grit. - Check the lid is fully closed — the maker lists it first, and a lid not registering as shut stops the fill on these machines. ### Where this goes next The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. Top-load washers What this one means What E1 means on this make The machine gave up waiting for a water level it never reached. What is useful about this code is how much of it is outside the appliance: two taps, two hoses and two screens, and the screens are where this climate does its work — fine grit and scale collect on the mesh in the inlet valve until the fill slows past the timer. A machine in a condominium laundry closet is also a machine whose taps are behind it and have not been fully opened since the day it was delivered. Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. Which machines this one applies to Top-load washers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on four kinds of machine — the top-load washer, the dishwasher, the electric range and cooktop, and the refrigerator — and publishes none at all for its dryers, its freezers, its wine cabinets or its ice machines. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door. What to do about it Open both taps fully — not most of the way. A half-open cold tap fills slowly enough to trigger this and fast enough to look normal. Pull the machine forward and look at the hoses. A hose kinked when the appliance was pushed back is the single most common cause here. Close the taps, unscrew the hoses at the machine, and clean the screens in the inlet. They are behind the connection and they clog with grit. Check the lid is fully closed — the maker lists it first, and a lid not registering as shut stops the fill on these machines. Where this goes next The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. --- **[Read full article: Washer error code E1](https://frigidairemiami.support/error-codes/washer-e1/)**