--- title: "Washer error code E3" description: "Frigidaire washer error code E3: The machine is not refusing to work, it does not believe the lid is shut." url: "https://frigidairemiami.support/error-codes/washer-e3/" date_modified: "2026-09-09" Appliance type: "washer" --- # Washer error code E3 ### What E3 means on this make The machine is not refusing to work, it does not believe the lid is shut. On the top-loaders this badge builds, that belief comes from a lock that engages at the start of the cycle, and it fails in two ways worth telling apart: a lid that is genuinely not latching because the machine has crept out of level, and a lock that no longer confirms it engaged. The maker names both, and it names the level check first — which matches what we find in laundry closets with tiled floors. ### Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. ### Which machines this one applies to Top-load washers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on four kinds of machine — the top-load washer, the dishwasher, the electric range and cooktop, and the refrigerator — and publishes none at all for its dryers, its freezers, its wine cabinets or its ice machines. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door. ### What to do about it - Close the lid firmly and watch the panel. If the code clears, the latch was not quite meeting the strike. - Check the machine is level and standing firm on all four feet. A cabinet leaning back holds its lid a few millimeters off the latch. - Cut power for a minute and restart the cycle. A lock that clears on a cold start and fails again mid-cycle is telling you it is the lock rather than the lid. - If it does not lock after starting, the maker’s own text says the lock or the board may have failed. Both are stocked parts and both are found with a meter. ### Where this goes next The job this usually becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. Top-load washers What this one means What E3 means on this make The machine is not refusing to work, it does not believe the lid is shut. On the top-loaders this badge builds, that belief comes from a lock that engages at the start of the cycle, and it fails in two ways worth telling apart: a lid that is genuinely not latching because the machine has crept out of level, and a lock that no longer confirms it engaged. The maker names both, and it names the level check first — which matches what we find in laundry closets with tiled floors. Where this appears, and why not to clear it On the appliance’s own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker’s own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. Which machines this one applies to Top-load washers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on four kinds of machine — the top-load washer, the dishwasher, the electric range and cooktop, and the refrigerator — and publishes none at all for its dryers, its freezers, its wine cabinets or its ice machines. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door. What to do about it Close the lid firmly and watch the panel. If the code clears, the latch was not quite meeting the strike. Check the machine is level and standing firm on all four feet. A cabinet leaning back holds its lid a few millimeters off the latch. Cut power for a minute and restart the cycle. A lock that clears on a cold start and fails again mid-cycle is telling you it is the lock rather than the lid. If it does not lock after starting, the maker’s own text says the lock or the board may have failed. Both are stocked parts and both are found with a meter. Where this goes next The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call [(305) 615-5496](tel:+13056155496) and describe what the panel is doing before booking anything. --- **[Read full article: Washer error code E3](https://frigidairemiami.support/error-codes/washer-e3/)**