Error code
Washer error code E2
Frigidaire washer error code E2: The machine finished washing and could not empty itself in the time it allows. Which machines can raise it, what the maker publishes about it, and what to do next.
- From $89 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code E2, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
E2
The machine finished washing and could not empty itself in the time it allows. On these top-loaders the restriction is nearly always in the path rather than in the pump: a drain hose kinked behind the cabinet, a standpipe at the wrong height, or a coin sitting where the hose leaves the tub. The maker names the standpipe height first for a reason — a hose pushed too far down a standpipe siphons, and one too high asks the pump for more lift than it has.
or call (305) 615-5496
What it narrows down to
Error Code E2 means water takes too long to drain or is not draining properly.
Diagnostic
From $89, credited to the repair
On the same appliance
What else belongs to the washers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Error Code F2 indicates there is too much soap or wrong type of soap. Often, suds leak out or overflow.
Error Code E1 means water is not entering washer or slow water fill time.
Error Code E3 means wash lid is either open or the lid lock failed.
Error Code E4 means the unit is out of balance during spin operation.
Error Code E5 means the unit is not level.
Error Code CL means the unit lid is open for more than 20 seconds with control lock activated.
The same digits mean different things on different equipment. Search the full code list
In more detail
About Washer error code E2
What E2 means on this make
The machine finished washing and could not empty itself in the time it allows. On these top-loaders the restriction is nearly always in the path rather than in the pump: a drain hose kinked behind the cabinet, a standpipe at the wrong height, or a coin sitting where the hose leaves the tub. The maker names the standpipe height first for a reason — a hose pushed too far down a standpipe siphons, and one too high asks the pump for more lift than it has.
Where this appears, and why not to clear it
On the appliance's own display, as a short single code — a letter and a number, or two letters. Nothing alternates and nothing arrives in halves on this make, so what the panel shows is the whole of it. Photograph it before you cut the power. This maker's own answer to most of these is thirty seconds at the breaker, and that is worth following once — but a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again.
Which machines this one applies to
Top-load washers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on four kinds of machine — the top-load washer, the dishwasher, the electric range and cooktop, and the refrigerator — and publishes none at all for its dryers, its freezers, its wine cabinets or its ice machines. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door.
What to do about it
- Look at the drain hose from the machine to the wall. Straighten anything kinked and check nothing is standing on it.
- Check how far the hose goes into the standpipe. Too deep siphons, too shallow floods, and both look like a pump problem.
- If the machine was installed or moved in the last thirty days, the maker asks that you go back to the installer — and in a condominium that is usually the right call.
- Close the lid and press Start/Pause. These machines will not spin with the lid open, and a load left full is often waiting on nothing more than that.
Where this goes next
The job this usually becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call (305) 615-5496 and describe what the panel is doing before booking anything.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards